Introducing the SpeedyBee F405 WING MINI Flight Controller, your ultimate companion for smooth and stable flights. Engineered with precision and compactness in mind, this mini marvel is tailor-made for winged aircraft enthusiasts. Equipped with an F405 processor, it ensures lightning-fast response times and unparalleled performance. Plus, its compact size makes installation a breeze, perfect for small-winged setups. Say hello to precision control and goodbye to turbulence with the SpeedyBee Wing Mini Flight Controller.
Features
- Tailor-made for Winged Aircraft
- Enhanced Performance
- Precision Control
- Compact Design
- Easy Installation
- F405 Processor
Specifications
PDB BOARD
- The VTX power interface Vv offers two power supply options: direct battery voltage or integrated BEC 5V (sharing the 5V4A Servo BEC voltage)
- Battery Current Sensor: 80A continuous, 150A peak Connected to FC board Current (Scale 195 in INAV, 50 A/V in ArduPilot)
- Battery Voltage Sensor: Connect to FC board VBAT, 1K:10K (Scale 1100 in INAV, BATT_VOLT_MULT 11.0 in ArduPilot)
- FC BEC output: Output 5.2V +/- 0.1V DC Continuous current 2 Amps, 3A Peak
- Servo BEC output: Output 5V +/- 0.1V DC Continuous current 4 Amps
- Input voltage range: 726V (26S LiPo)
- TVS Protective diode: Yes
- Weight: 5.5g
FC BOARD
- UART: 6 sets (USART1, USART2, USART3, UART4, UART5, UART6 – Dedicated for Wireless board Telemetry connection)
- Dual Analog Camera Switching: Switch between C1 and C2 using ArduPilot Relay or INAV Modes/USER
- LED: 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator (Red)
- PWM: 12x (9x pin headers + 2x solder pads + 1x “LED” pad)
- ADC: 4x (VBAT, Current, Analog RSSI, Analog AirSpeed)
- I2C: 1x Used for magnetometer, digital airspeed sensor
- ELRS/CRSF Receiver: Supported, connected to UART1
- SBUS: Built-in inverter for SBUS input (UART2-RX)
- IMU (Gyro & Accelerometer): ICM-42688-P
- MCU: STM32F405, 168MHz, 1MB Flash
- Analog RSSI: Supported, Named as “RS”
- Blackbox: MicroSD Card Slot
- Barometer: SPL006-001
- OSD Chip: AT7456E
- Weight: 5.6g
- Supported FC Firmware:
- INAV: SpeedyBeeF405WING (default)
- ArduPilot: SpeedyBeeF405WING
WIRELESS USB EXTENDER
- Buzzer: 5V Active Buzzer
- USB Port Type: Type-C
- Weight: 3.2g
Includes
- 1x 6pin-SH1.0mm GPS Module Cable without Connector on another end (250mm)
- 1x 4pin-SH1.0mm to 3pin-JST 1.25mm FPV Cam Cable (300mm)
- 1x 8pin-SH1.0mm Wireless USB Extender Cable (150mm)
- 1x F405 Wing Mini Standard-Install Shield Board
- 1x F405 Wing Mini Custom-Install Shield Board
- 1x 4pin-SH1.0mm Analog VTX Cable (300mm)
- 1x 6pin-SH1.0mm Digital VTX Cable (300mm)
- 1x 4pin Dupont Single-Head Cable (150mm)
- 1x F405 Wing Mini Wireless USB Extender
- 1x 35V 470uF Low ESR Capacitor
- 1x 90 Degree pin Header (3×10)
- 1x F405 Wing Mini PDB board
- 3x Straight Pin Header (1×10)
- 1x F405 Wing Mini FC board
- 1x Hardware Set
Reviews
There are no reviews yet.